Exporter • Supplier • Stockist of Stainless Steel GLOMET STAINLESS

Stainless Steel Coils

Stainless steel coils stocked by Glomet Stainless ASTM A240
Product Overview

SS Coils & Slit Strips

Glomet Stainless supplies hot rolled (No.1) and cold rolled (2B, BA) coils in stainless steel and duplex to ASTM A240 / ASME SA240, along with titanium and nickel alloy strip to ASTM B265 and the relevant ASTM B specifications.

Coils are slit to the width and weight that suit your tube mill, press line or roll former, with clean slit edges and the mill test certificate for each heat. Cut-to-length sheets from coil are also available.

0.3 – 12 mmThickness Range
8 – 1550 mmSlit / Mill Width
508 / 610 mmCoil Inner Diameter

01 Specifications

StandardASTM A240 / ASME SA240, ASTM A480
Titanium / NickelASTM B265 / B168, B443, B409, B424, B127, B575, B162
Cold Rolled0.3 mm – 3 mm thick
Hot Rolled2 mm – 12 mm thick
WidthMill width 1000 – 1550 mm; slit from 8 mm
Coil ID508 mm, 610 mm
Finish2B, BA, No.1, No.4, Hairline
FormHR Coil, CR Coil, Slit Coil, Strip
HardnessSoft Annealed, ¼ Hard, ½ Hard, Full Hard
EdgeMill Edge, Slit Edge
ProcessingSlitting, Cut to Length, PVC Coating
Test CertificateEN 10204 3.1; 3.2 on request

02 Grades

Austenitic, Ferritic & Martensitic Stainless
SS 304SS 304LSS 316SS 316LSS 316TiSS 321SS 347SS 310SSS 409SS 410SS 430SS 904L
Duplex & Super Duplex
Duplex 2205 (S31803 / S32205)Super Duplex 2507 (S32750)
Titanium
Titanium Gr 1Titanium Gr 2Titanium Gr 5
Nickel Alloys
Inconel 600Inconel 625Incoloy 800Incoloy 825Monel 400Hastelloy C276Nickel 200 / 201

03 Materials

Stainless Steel
Austenitic SS Coils
ASTM A240 / ASME SA240

304 and 316L 2B coils are the standard feed for welded tube mills, deep drawing and roll forming.

304/304L316/316L321310S
Ferritic
Ferritic & Martensitic Coils
ASTM A240 / ASME SA240

Nickel-free 409 and 430 for exhausts, appliances and trim; 410 where hardenability is needed.

409410430
Duplex
Duplex Coils
ASTM A240 / ASME SA240

High-strength feedstock for welded duplex tube and lightweight structural sections.

S31803S32205S32750
Ti & Nickel
Titanium & Nickel Alloy Strip
ASTM B265 / B168, B443, B127, B575

Narrow strip for heat exchanger plates, electronic parts, bellows and gaskets.

Ti Gr 2Inconel 600/625Monel 400C276

04 Chemical Composition

GradeCMnSiPSCrNiMoNOther
3040.082.000.750.0450.03018.0–20.08.0–10.5–0.10–
304L0.0302.000.750.0450.03017.5–19.58.0–12.0–0.10–
3160.082.000.750.0450.03016.0–18.010.0–14.02.00–3.000.10–
316L0.0302.000.750.0450.03016.0–18.010.0–14.02.00–3.000.10–
3210.082.000.750.0450.03017.0–19.09.0–12.0–0.10Ti 5×(C+N) – 0.70
310S0.082.001.500.0450.03024.0–26.019.0–22.0–––
4300.121.001.000.0400.03016.0–18.00.75–––
904L0.0202.001.000.0450.03519.0–23.023.0–28.04.0–5.00.10Cu 1.0–2.0
Duplex 2205 (S32205)0.0302.001.000.0300.02022.0–23.04.5–6.53.0–3.50.14–0.20–
GradeNiCrMoFeCuCMnSiOther
Titanium Gr 2–––0.30–0.08––O 0.25, N 0.03, H 0.015, Ti bal.
Inconel 60072.0 min14.0–17.0–6.0–10.00.500.151.000.50S 0.015
Inconel 62558.0 min20.0–23.08.0–10.05.0–0.100.500.50Nb+Ta 3.15–4.15
Incoloy 82538.0–46.019.5–23.52.5–3.522.0 min1.5–3.00.051.000.50Ti 0.6–1.2
Monel 40063.0 min––2.5028.0–34.00.302.000.50S 0.024
Hastelloy C276Balance14.5–16.515.0–17.04.0–7.0–0.0101.000.08W 3.0–4.5, Co 2.5
Nickel 20099.0 min––0.400.250.150.350.35S 0.01

Weight %, maximum unless a range is shown. The mill test certificate supplied with each heat is the controlling document.

05 Mechanical Properties

GradeTensile Strength (MPa, min)Yield Strength 0.2% (MPa, min)Elongation (% in 50 mm, min)Hardness (max)
30451520540201 HBW / 92 HRB
304L48517040201 HBW / 92 HRB
31651520540217 HBW / 95 HRB
316L48517040217 HBW / 95 HRB
32151520540217 HBW / 95 HRB
310S51520540217 HBW / 95 HRB
43045020522183 HBW / 89 HRB
904L4902203590 HRB
Duplex 2205 (S32205)65545025293 HBW / 31 HRC
GradeTensile Strength (MPa, min)Yield Strength 0.2% (MPa, min)Elongation (%, min)Condition
Titanium Gr 234527520Annealed
Inconel 60055024030Annealed
Inconel 62582741430Annealed (Grade 1)
Incoloy 82558624130Annealed
Monel 40048319335Annealed
Hastelloy C27669028340Solution Annealed
Nickel 20038010340Annealed

Room temperature values in the annealed condition. Temper-rolled (¼ hard and above) coils are supplied to the strength level ordered.

06 Applications

Welded tube manufacturing
Tube Making
Kitchen and dairy equipment
Appliances
Chemical process plant
Process Plant
Building and construction
Construction
Pharmaceutical equipment
Pharmaceutical
  • Feedstock for welded pipe and tube mills
  • Deep drawn sinks, utensils and appliance panels
  • Automotive exhaust systems and trims
  • Roll formed sections, channels and cable trays
  • Heat exchanger plates, gaskets and bellows
  • Press-shop blanks and stamped components

Get a Price for Coils

Tell us the grade, thickness, slit width, coil ID, finish and tonnage. We quote with stock availability and delivery time.

Request a Quote
Head Office

Plot No. 1534, Road No. 17, Sector KWC,
Steel Market, Kalamboli, Panvel,
Navi Mumbai – 410 218, Maharashtra, India