ASTM A276 / A479
Glomet Stainless supplies stainless steel round rods to ASTM A276 and A479, bright bars to A484 tolerances, and titanium and nickel alloy bars to ASTM B348 and the matching B specifications. Duplex bars are available for pump shafts and subsea hardware.
Bright drawn and centreless ground bars are held in common diameters of 304, 316L and 410. Bars are saw cut to length on request, and each bundle is tagged with grade, size and heat number to its mill test certificate.
304 and 316L for general machining, 303 for free-cutting, 410 where the part must be hardened.
303304/304L316/316L321410High strength and pitting resistance for pump shafts, valve stems and offshore fasteners.
S31803S32205S32750S32760Gr 2 for chemical hardware; Gr 5 for high-strength machined parts and fasteners.
Gr 1Gr 2Gr 5Gr 7Gr 12For valve trim, pump parts and fasteners in acid, sour and high temperature service.
Inconel 600/625Incoloy 800/825Monel 400C276Ni 200| Grade | C | Mn | Si | P | S | Cr | Ni | Mo | N | Other |
|---|---|---|---|---|---|---|---|---|---|---|
| 304 | 0.08 | 2.00 | 1.00 | 0.045 | 0.030 | 18.0–20.0 | 8.0–11.0 | – | – | – |
| 304L | 0.030 | 2.00 | 1.00 | 0.045 | 0.030 | 18.0–20.0 | 8.0–12.0 | – | – | – |
| 316 | 0.08 | 2.00 | 1.00 | 0.045 | 0.030 | 16.0–18.0 | 10.0–14.0 | 2.00–3.00 | – | – |
| 316L | 0.030 | 2.00 | 1.00 | 0.045 | 0.030 | 16.0–18.0 | 10.0–14.0 | 2.00–3.00 | – | – |
| 321 | 0.08 | 2.00 | 1.00 | 0.045 | 0.030 | 17.0–19.0 | 9.0–12.0 | – | – | Ti 5×C min – 0.70 |
| 310S | 0.08 | 2.00 | 1.50 | 0.045 | 0.030 | 24.0–26.0 | 19.0–22.0 | – | – | – |
| 410 | 0.08–0.15 | 1.00 | 1.00 | 0.040 | 0.030 | 11.5–13.5 | – | – | – | – |
| Duplex S32205 | 0.030 | 2.00 | 1.00 | 0.030 | 0.020 | 22.0–23.0 | 4.5–6.5 | 3.0–3.5 | 0.14–0.20 | – |
| Super Duplex S32750 | 0.030 | 1.20 | 0.80 | 0.035 | 0.020 | 24.0–26.0 | 6.0–8.0 | 3.0–5.0 | 0.24–0.32 | Cu 0.50 |
| Grade | Ni | Cr | Mo | Fe | Cu | C | Mn | Si | Other |
|---|---|---|---|---|---|---|---|---|---|
| Titanium Gr 2 | – | – | – | 0.30 | – | 0.08 | – | – | O 0.25, N 0.03, H 0.015, Ti bal. |
| Titanium Gr 5 | – | – | – | 0.40 | – | 0.08 | – | – | Al 5.5–6.75, V 3.5–4.5, O 0.20, Ti bal. |
| Inconel 600 | 72.0 min | 14.0–17.0 | – | 6.0–10.0 | 0.50 | 0.15 | 1.00 | 0.50 | S 0.015 |
| Inconel 625 | 58.0 min | 20.0–23.0 | 8.0–10.0 | 5.0 | – | 0.10 | 0.50 | 0.50 | Nb+Ta 3.15–4.15 |
| Incoloy 800 | 30.0–35.0 | 19.0–23.0 | – | 39.5 min | 0.75 | 0.10 | 1.50 | 1.00 | Al 0.15–0.60, Ti 0.15–0.60 |
| Incoloy 825 | 38.0–46.0 | 19.5–23.5 | 2.5–3.5 | 22.0 min | 1.5–3.0 | 0.05 | 1.00 | 0.50 | Ti 0.6–1.2 |
| Monel 400 | 63.0 min | – | – | 2.50 | 28.0–34.0 | 0.30 | 2.00 | 0.50 | S 0.024 |
| Hastelloy C276 | Balance | 14.5–16.5 | 15.0–17.0 | 4.0–7.0 | – | 0.010 | 1.00 | 0.08 | W 3.0–4.5, Co 2.5 |
| Nickel 200 | 99.0 min | – | – | 0.40 | 0.25 | 0.15 | 0.35 | 0.35 | S 0.01 |
Weight %, maximum unless a range is shown. The mill test certificate supplied with each heat is the controlling document.
| Grade | Tensile Strength (MPa, min) | Yield Strength 0.2% (MPa, min) | Elongation (% in 50 mm, min) | Reduction of Area (%, min) |
|---|---|---|---|---|
| 304 | 515 | 205 | 40 | 50 |
| 304L | 485 | 170 | 40 | 50 |
| 316 | 515 | 205 | 40 | 50 |
| 316L | 485 | 170 | 40 | 50 |
| 321 | 515 | 205 | 40 | 50 |
| 310S | 515 | 205 | 40 | 50 |
| 410 (Annealed) | 485 | 275 | 20 | 45 |
| Duplex S32205 | 655 | 450 | 25 | – |
| Super Duplex S32750 | 800 | 550 | 15 | – |
| Grade | Tensile Strength (MPa, min) | Yield Strength 0.2% (MPa, min) | Elongation (%, min) | Condition |
|---|---|---|---|---|
| Titanium Gr 2 | 345 | 275 | 20 | Annealed |
| Titanium Gr 5 | 895 | 828 | 10 | Annealed |
| Inconel 600 | 550 | 240 | 30 | Annealed |
| Inconel 625 | 827 | 414 | 30 | Annealed (Grade 1) |
| Incoloy 800 | 520 | 205 | 30 | Annealed |
| Incoloy 825 | 586 | 241 | 30 | Annealed |
| Monel 400 | 483 | 172 | 35 | Annealed |
| Hastelloy C276 | 690 | 283 | 40 | Solution Annealed |
| Nickel 200 | 380 | 103 | 40 | Annealed |
Room temperature values for annealed bar. Cold drawn and strain hardened bars are supplied to the strength level ordered.





Tell us the grade, diameter, finish, tolerance, length and quantity. We quote with stock availability and delivery time.