ASTM A193 / A194
Glomet Stainless supplies stainless steel bolts, stud bolts and threaded rods to ASTM A193, nuts to ASTM A194 and general-purpose fasteners to ISO 3506 (A2 and A4) and ASTM F593 / F594. Duplex, titanium and nickel alloy fasteners are made from certified bar stock for corrosive and high temperature service.
Hex bolts, nuts and washers in A2 and A4 are held in common metric sizes. Flange stud bolt sets are cut and threaded to ASME B16.5 lengths, and special fasteners are machined to your drawing. Heads are marked with grade and manufacturer’s identification as the standard requires.
Stud bolts and heavy hex nuts for flanged joints on pressure piping and vessels.
B8 / 8B8M / 8MB8T / 8TB8C / 8CA2 (304) for general fixing, A4 (316) for marine, food and chemical environments.
A2-70A2-80A4-70A4-80For offshore, seawater and chloride service where A4 fasteners would pit or crack.
S31803S32750S32760Ti Gr 2Ti Gr 5High strength, heat and acid resistant bolting for furnaces, turbines and sour service.
Inconel 625Inconel 718Monel 400Monel K500C276| Grade | C | Mn | Si | P | S | Cr | Ni | Mo | N | Other |
|---|---|---|---|---|---|---|---|---|---|---|
| B8 (304) | 0.08 | 2.00 | 1.00 | 0.045 | 0.030 | 18.0–20.0 | 8.0–11.0 | – | – | – |
| B8M (316) | 0.08 | 2.00 | 1.00 | 0.045 | 0.030 | 16.0–18.0 | 10.0–14.0 | 2.00–3.00 | – | – |
| B8T (321) | 0.08 | 2.00 | 1.00 | 0.045 | 0.030 | 17.0–19.0 | 9.0–12.0 | – | – | Ti 5×C min – 0.70 |
| B8C (347) | 0.08 | 2.00 | 1.00 | 0.045 | 0.030 | 17.0–19.0 | 9.0–13.0 | – | – | Nb 10×C min – 1.10 |
| A2 (ISO 3506) | 0.10 | 2.00 | 1.00 | 0.050 | 0.030 | 15.0–20.0 | 8.0–19.0 | – | – | Cu 4.0 |
| A4 (ISO 3506) | 0.08 | 2.00 | 1.00 | 0.045 | 0.030 | 16.0–18.5 | 10.0–15.0 | 2.00–3.00 | – | Cu 4.0 |
| Duplex S32205 | 0.030 | 2.00 | 1.00 | 0.030 | 0.020 | 22.0–23.0 | 4.5–6.5 | 3.0–3.5 | 0.14–0.20 | – |
| Super Duplex S32750 | 0.030 | 1.20 | 0.80 | 0.035 | 0.020 | 24.0–26.0 | 6.0–8.0 | 3.0–5.0 | 0.24–0.32 | Cu 0.50 |
| Grade | Ni | Cr | Mo | Fe | Cu | C | Mn | Si | Other |
|---|---|---|---|---|---|---|---|---|---|
| Titanium Gr 2 | – | – | – | 0.30 | – | 0.08 | – | – | O 0.25, N 0.03, H 0.015, Ti bal. |
| Titanium Gr 5 | – | – | – | 0.40 | – | 0.08 | – | – | Al 5.5–6.75, V 3.5–4.5, O 0.20, Ti bal. |
| Inconel 625 | 58.0 min | 20.0–23.0 | 8.0–10.0 | 5.0 | – | 0.10 | 0.50 | 0.50 | Nb+Ta 3.15–4.15 |
| Inconel 718 | 50.0–55.0 | 17.0–21.0 | 2.80–3.30 | Balance | 0.30 | 0.08 | 0.35 | 0.35 | Nb+Ta 4.75–5.50, Ti 0.65–1.15, Al 0.20–0.80 |
| Monel 400 | 63.0 min | – | – | 2.50 | 28.0–34.0 | 0.30 | 2.00 | 0.50 | S 0.024 |
| Hastelloy C276 | Balance | 14.5–16.5 | 15.0–17.0 | 4.0–7.0 | – | 0.010 | 1.00 | 0.08 | W 3.0–4.5, Co 2.5 |
Weight %, maximum unless a range is shown. The mill test certificate supplied with each heat is the controlling document.
| Grade / Class | Size | Tensile Strength (MPa, min) | Yield / 0.2% Proof (MPa, min) | Elongation (min) | Hardness (max) |
|---|---|---|---|---|---|
| B8, B8M, B8T, B8C – Class 1 | All | 515 | 205 | 30% | 223 HBW |
| B8 – Class 2 | Up to 3/4" | 860 | 690 | 12% | 321 HBW |
| B8M – Class 2 | Up to 3/4" | 760 | 655 | 15% | 321 HBW |
| A2-70 / A4-70 | Up to M24 | 700 | 450 | 0.4d | – |
| A2-80 / A4-80 | Up to M24 | 800 | 600 | 0.3d | – |
| Grade | Tensile Strength (MPa, min) | Yield Strength 0.2% (MPa, min) | Elongation (%, min) | Condition |
|---|---|---|---|---|
| Titanium Gr 2 | 345 | 275 | 20 | Annealed |
| Titanium Gr 5 | 895 | 828 | 10 | Annealed |
| Inconel 625 | 827 | 414 | 30 | Annealed (Grade 1) |
| Inconel 718 | 1275 | 1034 | 12 | Solution Treated & Aged |
| Monel 400 | 483 | 172 | 35 | Annealed |
| Hastelloy C276 | 690 | 283 | 40 | Solution Annealed |
Class 2 (strain hardened) strengths fall as diameter increases. A194 nuts are supplied to the proof load and hardness of the ordered grade.





Send the fastener list with type, grade, diameter, length, thread and quantity — or your drawing. We quote with delivery time.