ASME B16.5
Glomet Stainless supplies forged stainless steel and duplex flanges to ASTM A182 / ASME SA182, titanium flanges to ASTM B381 and nickel alloy flanges to ASTM B564 — machined to ASME B16.5, B16.47, EN 1092-1 and other national standards.
Weld neck, slip on and blind flanges in F304L and F316L are held in common classes. Bore is matched to your pipe schedule, facing is finished to the specified roughness, and every flange is stamped with grade, size, class and heat number.
Dual-certified F304/F304L and F316/F316L flanges for process, utility and food-grade piping.
F304/304LF316/316LF321F347For seawater cooling, firewater rings, offshore topsides and desalination.
F51F60F53F55F44Lightweight, corrosion-proof flanges for chlorine, brine and marine piping.
F-1F-2F-5F-7For acid, sour gas and high temperature systems where the pipe itself is a nickel alloy.
Inconel 600/625Incoloy 800/825Monel 400C276| Grade | C | Mn | Si | P | S | Cr | Ni | Mo | N | Other |
|---|---|---|---|---|---|---|---|---|---|---|
| F304 | 0.08 | 2.00 | 1.00 | 0.045 | 0.030 | 18.0–20.0 | 8.0–11.0 | – | – | – |
| F304L | 0.030 | 2.00 | 1.00 | 0.045 | 0.030 | 18.0–20.0 | 8.0–12.0 | – | – | – |
| F316 | 0.08 | 2.00 | 1.00 | 0.045 | 0.030 | 16.0–18.0 | 10.0–14.0 | 2.00–3.00 | – | – |
| F316L | 0.030 | 2.00 | 1.00 | 0.045 | 0.030 | 16.0–18.0 | 10.0–14.0 | 2.00–3.00 | – | – |
| F321 | 0.08 | 2.00 | 1.00 | 0.045 | 0.030 | 17.0–19.0 | 9.0–12.0 | – | – | Ti 5×C min – 0.70 |
| F347 | 0.08 | 2.00 | 1.00 | 0.045 | 0.030 | 17.0–20.0 | 9.0–13.0 | – | – | Nb 10×C min – 1.10 |
| F51 (S31803) | 0.030 | 2.00 | 1.00 | 0.030 | 0.020 | 21.0–23.0 | 4.5–6.5 | 2.5–3.5 | 0.08–0.20 | – |
| F60 (S32205) | 0.030 | 2.00 | 1.00 | 0.030 | 0.020 | 22.0–23.0 | 4.5–6.5 | 3.0–3.5 | 0.14–0.20 | – |
| F53 (S32750) | 0.030 | 1.20 | 0.80 | 0.035 | 0.020 | 24.0–26.0 | 6.0–8.0 | 3.0–5.0 | 0.24–0.32 | Cu 0.50 |
| F55 (S32760) | 0.030 | 1.00 | 1.00 | 0.030 | 0.010 | 24.0–26.0 | 6.0–8.0 | 3.0–4.0 | 0.20–0.30 | Cu 0.50–1.00, W 0.50–1.00 |
| Grade | Ni | Cr | Mo | Fe | Cu | C | Mn | Si | Other |
|---|---|---|---|---|---|---|---|---|---|
| Titanium F-2 | – | – | – | 0.30 | – | 0.08 | – | – | O 0.25, N 0.03, H 0.015, Ti bal. |
| Titanium F-5 | – | – | – | 0.40 | – | 0.08 | – | – | Al 5.5–6.75, V 3.5–4.5, O 0.20, Ti bal. |
| Inconel 600 | 72.0 min | 14.0–17.0 | – | 6.0–10.0 | 0.50 | 0.15 | 1.00 | 0.50 | S 0.015 |
| Inconel 625 | 58.0 min | 20.0–23.0 | 8.0–10.0 | 5.0 | – | 0.10 | 0.50 | 0.50 | Nb+Ta 3.15–4.15 |
| Incoloy 800 | 30.0–35.0 | 19.0–23.0 | – | 39.5 min | 0.75 | 0.10 | 1.50 | 1.00 | Al 0.15–0.60, Ti 0.15–0.60 |
| Incoloy 825 | 38.0–46.0 | 19.5–23.5 | 2.5–3.5 | 22.0 min | 1.5–3.0 | 0.05 | 1.00 | 0.50 | Ti 0.6–1.2 |
| Monel 400 | 63.0 min | – | – | 2.50 | 28.0–34.0 | 0.30 | 2.00 | 0.50 | S 0.024 |
| Hastelloy C276 | Balance | 14.5–16.5 | 15.0–17.0 | 4.0–7.0 | – | 0.010 | 1.00 | 0.08 | W 3.0–4.5, Co 2.5 |
Weight %, maximum unless a range is shown. The mill test certificate supplied with each heat is the controlling document.
| Grade | Tensile Strength (MPa, min) | Yield Strength 0.2% (MPa, min) | Elongation (%, min) | Reduction of Area (%, min) |
|---|---|---|---|---|
| F304 | 515 | 205 | 30 | 50 |
| F304L | 485 | 170 | 30 | 50 |
| F316 | 515 | 205 | 30 | 50 |
| F316L | 485 | 170 | 30 | 50 |
| F321 | 515 | 205 | 30 | 50 |
| F347 | 515 | 205 | 30 | 50 |
| F51 (S31803) | 620 | 450 | 25 | 45 |
| F60 (S32205) | 655 | 450 | 25 | 45 |
| F53 (S32750) | 800 | 550 | 15 | – |
| F55 (S32760) | 750 | 550 | 25 | 45 |
| Grade | Tensile Strength (MPa, min) | Yield Strength 0.2% (MPa, min) | Elongation (%, min) | Condition |
|---|---|---|---|---|
| Titanium F-2 | 345 | 275 | 20 | Annealed |
| Titanium F-5 | 895 | 828 | 10 | Annealed |
| Inconel 600 | 550 | 240 | 30 | Annealed |
| Inconel 625 | 827 | 414 | 30 | Annealed |
| Incoloy 800 | 520 | 205 | 30 | Annealed |
| Incoloy 825 | 586 | 241 | 30 | Annealed |
| Monel 400 | 483 | 172 | 35 | Annealed |
| Hastelloy C276 | 690 | 283 | 40 | Solution Annealed |
Room temperature values for solution annealed forgings. Limits can vary with section thickness — confirm against the ordered specification.





Send the flange type, grade, size, class, facing and bore schedule. We quote with stock availability and delivery time.