ASTM A403
Glomet Stainless supplies seamless and welded buttweld fittings to ASTM A403 / ASME SA403 in ASME B16.9 dimensions, and forged socket weld and threaded fittings to ASTM A182 in ASME B16.11 dimensions. Duplex, titanium and nickel alloy fittings are supplied to ASTM A815, B363 and B366.
Elbows, tees, reducers and caps in 304L and 316L are held in common schedules so a fitting matches the pipe you buy from us. Every piece is stencilled with grade, size, schedule and heat number.
WP304L and WP316L buttweld fittings and F304L / F316L forged fittings for general process piping.
WP304/304LWP316/316LWP321WP347Matched to A790 duplex pipe for seawater, offshore and desalination systems.
S31803S32205S32750S32760Seamless and welded titanium fittings for chlorine, brine and seawater lines.
WPT1WPT2WPT5WPT7For acid, caustic and high temperature piping matched to nickel alloy pipe.
Inconel 600/625Incoloy 800/825Monel 400C276| Grade | C | Mn | Si | P | S | Cr | Ni | Mo | N | Other |
|---|---|---|---|---|---|---|---|---|---|---|
| WP 304 | 0.08 | 2.00 | 1.00 | 0.045 | 0.030 | 18.0–20.0 | 8.0–11.0 | – | – | – |
| WP 304L | 0.030 | 2.00 | 1.00 | 0.045 | 0.030 | 18.0–20.0 | 8.0–12.0 | – | – | – |
| WP 316 | 0.08 | 2.00 | 1.00 | 0.045 | 0.030 | 16.0–18.0 | 10.0–14.0 | 2.00–3.00 | – | – |
| WP 316L | 0.030 | 2.00 | 1.00 | 0.045 | 0.030 | 16.0–18.0 | 10.0–14.0 | 2.00–3.00 | – | – |
| WP 321 | 0.08 | 2.00 | 1.00 | 0.045 | 0.030 | 17.0–19.0 | 9.0–12.0 | – | – | Ti 5×C min – 0.70 |
| WP 347 | 0.08 | 2.00 | 1.00 | 0.045 | 0.030 | 17.0–19.0 | 9.0–13.0 | – | – | Nb 10×C min – 1.10 |
| WP 310S | 0.08 | 2.00 | 1.00 | 0.045 | 0.030 | 24.0–26.0 | 19.0–22.0 | – | – | – |
| WP S31803 | 0.030 | 2.00 | 1.00 | 0.030 | 0.020 | 21.0–23.0 | 4.5–6.5 | 2.5–3.5 | 0.08–0.20 | – |
| WP S32750 | 0.030 | 1.20 | 0.80 | 0.035 | 0.020 | 24.0–26.0 | 6.0–8.0 | 3.0–5.0 | 0.24–0.32 | Cu 0.50 |
| Grade | Ni | Cr | Mo | Fe | Cu | C | Mn | Si | Other |
|---|---|---|---|---|---|---|---|---|---|
| Titanium Gr 2 | – | – | – | 0.30 | – | 0.08 | – | – | O 0.25, N 0.03, H 0.015, Ti bal. |
| Inconel 600 | 72.0 min | 14.0–17.0 | – | 6.0–10.0 | 0.50 | 0.15 | 1.00 | 0.50 | S 0.015 |
| Inconel 625 | 58.0 min | 20.0–23.0 | 8.0–10.0 | 5.0 | – | 0.10 | 0.50 | 0.50 | Nb+Ta 3.15–4.15 |
| Incoloy 800 | 30.0–35.0 | 19.0–23.0 | – | 39.5 min | 0.75 | 0.10 | 1.50 | 1.00 | Al 0.15–0.60, Ti 0.15–0.60 |
| Incoloy 825 | 38.0–46.0 | 19.5–23.5 | 2.5–3.5 | 22.0 min | 1.5–3.0 | 0.05 | 1.00 | 0.50 | Ti 0.6–1.2 |
| Monel 400 | 63.0 min | – | – | 2.50 | 28.0–34.0 | 0.30 | 2.00 | 0.50 | S 0.024 |
| Hastelloy C276 | Balance | 14.5–16.5 | 15.0–17.0 | 4.0–7.0 | – | 0.010 | 1.00 | 0.08 | W 3.0–4.5, Co 2.5 |
| Nickel 200 | 99.0 min | – | – | 0.40 | 0.25 | 0.15 | 0.35 | 0.35 | S 0.01 |
Weight %, maximum unless a range is shown. The mill test certificate supplied with each heat is the controlling document.
| Grade | Tensile Strength (MPa, min) | Yield Strength 0.2% (MPa, min) | Elongation (%, min) | Hardness (max) |
|---|---|---|---|---|
| WP 304 | 515 | 205 | 28 | – |
| WP 304L | 485 | 170 | 28 | – |
| WP 316 | 515 | 205 | 28 | – |
| WP 316L | 485 | 170 | 28 | – |
| WP 321 | 515 | 205 | 28 | – |
| WP 347 | 515 | 205 | 28 | – |
| WP 310S | 515 | 205 | 28 | – |
| WP S31803 | 620 | 450 | 20 | 290 HBW |
| WP S32750 | 800 | 550 | 15 | 310 HBW |
| Grade | Tensile Strength (MPa, min) | Yield Strength 0.2% (MPa, min) | Elongation (%, min) | Condition |
|---|---|---|---|---|
| Titanium Gr 2 | 345 | 275 | 20 | Annealed |
| Inconel 600 | 550 | 240 | 30 | Annealed |
| Inconel 625 | 827 | 414 | 30 | Annealed (Grade 1) |
| Incoloy 800 | 520 | 205 | 30 | Annealed |
| Incoloy 825 | 586 | 241 | 30 | Annealed |
| Monel 400 | 483 | 193 | 35 | Annealed |
| Hastelloy C276 | 690 | 283 | 40 | Solution Annealed |
| Nickel 200 | 380 | 103 | 35 | Annealed |
Longitudinal values at room temperature. Fittings follow the mechanical requirements of the starting material specification.





Send the fitting list with type, grade, size, schedule or class and quantity. We quote with stock availability and delivery time.